compression stroke造句
例句与造句
- Then diesel fuel oil is injected or sprayed into the cylinder at the end of the compression stroke .
然后在压缩冲程即将结束时，柴油燃料被喷射或被喷雾进入气缸。 - Exchange - compression stroke
换气压缩行程 - It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
由模拟找出了压缩速度与压缩行程是两个影响成型压力极大的因素。 - It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
由仿真找出了压缩速度与压缩行程是两个影响成型压力极大的因素。 - Using lower switch time , lower compression speed and higher compression stroke will result in lower cavity pressures
使用较短的切换时间、较低的压缩速度以及较高的压缩行程将产生较低的模安穴压力。 - It's difficult to find compression stroke in a sentence. 用compression stroke造句挺难的
- This is the four - stroke cycle which is in common use . an alternative is the two - stroke cycle , which combines the exhaust and compression strokes into one
这就是常用的四冲程循环。另一种循环是两冲程循环，它把排气冲程与压缩冲程合并为一个冲程。 - When the engine runs in compression stroke and power stroke , the valves must close tightly on their seats to produce a gas - tight seal and thus prevent the gases escaping from the combustion chamber
当发动机处于压缩行程和做功行程时，阀门必须紧紧地关闭以产生一个不透气的气封，以防止气体逃离燃烧室。 - In this paper , the general theory and numerical solution procedure were described . by building a diesel modeling with vertical valves and a piston bowl , a whole cycle was calculated , which include intake stroke , compression stroke , expansion stroke and exhaust stroke
通过对带有进、排气门的柴油机进行计算，模拟了一个完整循环内进气道、气门和缸内气体流动的全过程。 - Simulation and the associated numerical algorithm on the injection - compression molding ( icm ) process were developed to understand processing characteristics by changing processing parameters including compression speed , switch time from injection to compression , compression stroke as well as initial cavity thickness and part thickness using disk parts
摘要射出压缩成型的仿真以及数值运算是要了解成型参数的改变，包括：压缩速度、射出与封装的切换时间、压缩行程等制程特性而创建的，同时也包含了初始的开模厚度以及使用在光盘片的成品厚度。 - On the basis mentioned above , another mathematical model for the supercharged diesel was set up . according to this model some results of simulation calculations were given . the characteristics of operation of the diesel in wet compression : including the excess air coefficient , the cylinder temperature at the beginning of compression stroke , the maximum temperature in the cylinder , the cylinder thermal load , the specific fuel consumption , and efficiency of diesel engine were obtained
在此基础上，又建立了增压柴油机湿压缩的数学模型，对喷水后柴油机的各性能参数，诸如过量空气系数、气缸进气温度，缸内最高温度、气缸热负荷、比油耗、热效率等进行了仿真计算，为增压柴油机进口加湿技术的研究提供了理论依据。 - Simulation and the associated numerical algorithm on the injection - compression molding ( icm ) process were developed to understand processing characteristics by changing processing parameters including compression speed , switch time from injection to compression , compression stroke as well as initial cavity thickness and part thickness using disk parts
摘要射出压缩成型的模拟以及数值运算是要了解成型参数的改变，包括：压缩速度、射出与压缩的切换时间、压缩行程等制程特性而建立的，同时也包含了初始的开模厚度以及使用在光碟片的成品厚度。